-
Toevoegen aan winkelwagenQuick ViewCim-Tek 800 hydroglass particulate element 2 μ CT70037
€99,00 €119,79 tax incl.Cim-tek filters are an economical and effective way to remove emulsified water, particulate and micro-organism from fuel and oil. Free water is best removed using a water separator – preferably before the fuel pump, as the water does make the Cim-teks block. we recommend Separ or Racor water separators. Cim-tek elements either only take out particulate or both particulate and emulsified water. They are available with nominal cellulose filter elements as well as the much more effective absolute glass fibre based filter elements, and then with or without absorption material to eliminate the emulsified water from the fuel or oil. The latter prevents the growth of micro-organism. Different element and filter head sizes are for different pump flow rate rates. The lower the micronnage on the filter, the better it filters and removes water.
Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewAir Sentry D-102 air breather
€172,85 €209,15 tax incl.1″ slip fit, max water absorption capacity 489 ml ( 16.56 fl.oz.)
max reservoir fluid flow 570 lpm or 150 gpm
100% Silica Gel
max air flow 20 cfm (0,56 m3/minute)
Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewVacuum Gauge
€15,12 €18,30 tax incl.Compound vacuum gauge for Separ Filter SWK-2000 Series of fuel water separators.
Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewFilter element 01830 SWK2000/18 30μ
€25,41 €30,75 tax incl.The SEPAR 2000 should be installed on the suction side of the fuel system, between the fuel feed tank and the engine mounted fuel lift pump.
Install the filter in an accessible position to allow water and particulate removal and filter element change (a minimum of 60mm is required for element change)
Separ 2000 series of fuel/water separators are compatible with B100 biodiesel.
Separ 2000 series water separators fuel filters are a simple solution to many different fuel related problems.
Five separate stages of filtration ensure 99.9% water separation (Certified TUV Report using SAE J1839) at maximum flow.
Low restriction reduces wear on fuel pumps and ensures full RPMs.
Back flushable (cleanable) element reduces down time and costly element changes.
The ideal position for the filter is at the same height as the lift pump. However if the top of the fuel tank is above this position a full flow ball valve should be fitted, before, the filter so that the fuel flow can be shut off to allow filter maintenance.
In applications where the fuel level is below the filter it is still advisable to install a full flow ball valve to prevent fuel draining back into the fuel tank.Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewCim-Tek 800 particulate element 2 μ CT70814
€65,38 €79,11 tax incl.Cim-tek filters are an economical and effective way to remove emulsified water, particulate and micro-organism from fuel and oil. Free water is best removed using a water separator – preferably before the fuel pump, as the water does make the Cim-teks block. we recommend Separ or Racor water separators. Cim-tek elements either only take out particulate or both particulate and emulsified water. They are available with nominal cellulose filter elements as well as the much more effective absolute glass fibre based filter elements, and then with or without absorption material to eliminate the emulsified water from the fuel or oil. The latter prevents the growth of micro-organism. Different element and filter head sizes are for different pump flow rate rates. The lower the micronnage on the filter, the better it filters and removes water.
Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewFilter element 01030 SWK2000/10 30μ
€16,70 €20,21 tax incl.The SEPAR 2000 should be installed on the suction side of the fuel system, between the fuel feed tank and the engine mounted fuel lift pump.
Install the filter in an accessible position to allow water and particulate removal and filter element change (a minimum of 60mm is required for element change)
Separ 2000 series of fuel/water separators are compatible with B100 biodiesel.
Separ 2000 series water separators fuel filters are a simple solution to many different fuel related problems.
Five separate stages of filtration ensure 99.9% water separation (Certified TUV Report using SAE J1839) at maximum flow.
Low restriction reduces wear on fuel pumps and ensures full RPMs.
Back flushable (cleanable) element reduces down time and costly element changes.
The ideal position for the filter is at the same height as the lift pump. However if the top of the fuel tank is above this position a full flow ball valve should be fitted, before, the filter so that the fuel flow can be shut off to allow filter maintenance.
In applications where the fuel level is below the filter it is still advisable to install a full flow ball valve to prevent fuel draining back into the fuel tank.Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewCim-Tek 260 hydroglass element 10 μ CT70236
€76,42 €92,47 tax incl.Cim-tek filters are an economical and effective way to remove emulsified water, particulate and micro-organism from fuel and oil. Free water is best removed using a water separator – preferably before the fuel pump, as the water does make the Cim-teks block. we recommend Separ or Racor water separators. Cim-tek elements either only take out particulate or both particulate and emulsified water. They are available with nominal cellulose filter elements as well as the much more effective absolute glass fibre based filter elements, and then with or without absorption material to eliminate the emulsified water from the fuel or oil. The latter prevents the growth of micro-organism. Different element and filter head sizes are for different pump flow rate rates. The lower the micronnage on the filter, the better it filters and removes water.
Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewCim-Tek 800 hydroglass particulate element 10 μ CT70024
€84,70 €102,49 tax incl.Spin-on filters are an economical and efficient way to get emulsified water, particulate and micro-organism from fuel and oil. Free water should be taken out using a water separator – preferably before the fuel pump. Elements either just take out particulate or both particulate and emulsified water. Elements are available with nominal cellulose elements as well as absolute glass fibre based filter elements. Absorption material is used to get the emulsified water out of the fuel or oil. Different sizes for different flow rate ranges.
Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewKolor Kut Modified
€21,63 €26,17 tax incl.Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewFilter element 00530/50 SWK2000/5/50 30μ
€14,26 €17,25 tax incl.The SEPAR 2000 should be installed on the suction side of the fuel system, between the fuel feed tank and the engine mounted fuel lift pump.
Install the filter in an accessible position to allow water and particulate removal and filter element change (a minimum of 60mm is required for element change)
Separ 2000 series of fuel/water separators are compatible with B100 biodiesel.
Separ 2000 series water separators fuel filters are a simple solution to many different fuel related problems.
Five separate stages of filtration ensure 99.9% water separation (Certified TUV Report using SAE J1839) at maximum flow.
Low restriction reduces wear on fuel pumps and ensures full RPMs.
Back flushable (cleanable) element reduces down time and costly element changes.
The ideal position for the filter is at the same height as the lift pump. However if the top of the fuel tank is above this position a full flow ball valve should be fitted, before, the filter so that the fuel flow can be shut off to allow filter maintenance.
In applications where the fuel level is below the filter it is still advisable to install a full flow ball valve to prevent fuel draining back into the fuel tank.Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewElement 2020SM-OR 2 micron for Turbine 1000 series
€30,63 €37,06 tax incl.Toevoegen aan winkelwagenQuick View -
Toevoegen aan winkelwagenQuick ViewWater alarm kit RK30880E
€209,69 €253,72 tax incl.Specifications:
- Port Thread Size 1/2″-20 UNF
- Housing Glass-filled Nylon
- Volts DC 12 or 24
- Ohm (trigger threshold) 47K Ambient
- Fuel Temperature -400 to +2500F (-400 to +1210C)
Toevoegen aan winkelwagenQuick View
Ask for best offer
Order before 15:00 on working days , same day shipping for products in stock
